Kuverengera Mienzaniso - Shenzhen HONGSBELT

Horizontal Conveyor

Mufekitori yekudyara nyama, tembiricha yakadzika inodzorwa mu21 ° C, uye yakagamuchira HS-100 yemutsetse wekugadzirisa nyama.Huremu hwepakati hwenyama ndeye 60kg/M2.Upamhi hwebhandi i600mm, uye hurefu hwese hwemutakuri ndeye 30M mune yakachinjika dhizaini.The conveyor bhandi kushanda kumhanya iri 18M/min muunyoro uye kutonhora nharaunda.Iyo conveyor inotanga mukuburitsa uye hapana kuunganidza mamiriro.Iyo inotora sprockets ine mazino masere mu192mm dhayamita, uye iyo 38mm x 38mm Stainless simbi drive shaft.Iyo yakakodzera calculation formula ndeiyi inotevera.

Kuverengera kweyuniti theory tension - TB

FORMULA :	TB =〔 (WP + 2 WB) × FBW + Wf 〕× L + (WP × H)
	TB =〔 ( 60 + ( 2 × 8.6 ) × 0.12 〕× 30 = 278 (kg / M)
	Nekuda kweiyo haisi yekuunganidza kutakura, Wf inogona kufuratirwa.

Kuverengera kweyuniti kushushikana - TW

FORMULA :	TW = TB × FA
	TW = 278 × 1.0 = 278 ( Kg / M )

Kuverengera kweyuniti inotenderwa tension - TA

FORMULA :	TA = BS × FS × FT
	TA = 1445 × 1.0 × 0.95 = 1372.75 ( Kg / M )
	Nekuda kweTA kukosha kwakakura kupfuura TW, Naizvozvo, kutora neHS-100 ndiko kusarudzwa kwakakodzera.

Ndokumbira utarise kuSprocket spacing yeHS-100 muDrive Sprockets Chapter;iyo yakanyanya sprocket spacing ingangoita 140mm yeiyi dhizaini.Ese ari maviri dhiraivha / Idler kupera kwemutakuri anofanirwa kuiswa aine matatu sprockets.

Deflection ratio ye drive shaft - DS

FORMULA :	SL = (TW + SW) × BW
	SL = ( 278 + 11.48 ) × 0.6 = 173.7 ( Kg )
	Mukuenzanisa neMaximum Torque Factor muShaft Selection unit, tinoziva kuti kushandiswa kwe38mm × 38mm square shaft kwakachengeteka uye kwakakodzera kusarudzwa.

FORMULA :	DS = 5 × 10-4 × ( SL x SB3 / E x I )
	DS = 5 × 10-4 × [ (173.7 × 7003) / ( 19700 × 174817 ) ] = 0.0086
	Kana mhedzisiro yekuverenga iri diki pane yakajairwa kukosha yakanyorwa muDeflection Table;kutora maviri bhora mabheji zvakakwana kune system.

Kuverenga kwe shaft torque - TS

FORMULA :	TS = TW × BW × R
	TS = 10675 ( kg - mm)
	Mukuenzanisa neMaximum Torque Factor muShaft Selection unit, tinoziva kuti kushandiswa kwe50mm × 50mm square shaft kwakachengeteka uye kwakakodzera kusarudzwa.

Kuverenga kweHorsepower - HP

FORMULA :	HP = 2.2 × 10-4 × [ ( TS × V ) / R ]
	HP = 2.2 × 10-4 × [ ( 10675 × 10) / 66.5] = 0.32 ( HP )
	Kazhinji, iyo mechanic simba rekutendeuka conveyor inogona kurasikirwa ne11% panguva yekushanda.
	MHP = [ 0.32 / (100 - 11) ]× 100 = 0.35 (HP)
	Kutora iyo 1/2HP drive mota ndiyo sarudzo chaiyo.

Isu tinonyora mienzaniso inoshanda muchitsauko chino chereferensi yako, uye tinokutungamira kuti uverenge kuti uedze uye kuona mhedzisiro yekuverenga.

Center Driven Conveyor

Iyo yakaunganidzwa conveyor inowanzo shandiswa muindasitiri yekunwa.Dhizaini yemutakuri ndeye 2M muhupamhi uye 6M mukureba kwefuremu.Kumhanya kwekushanda kwemutakuri uri mu20M/min;inotanga mumamiriro ezvinhu ezvigadzirwa zvinounganidza pabhanhire uye inoshanda mu 30 ℃ yakaoma nharaunda.Kurodha kwebhandi ndeye 80Kg/m2 uye zvigadzirwa zvekutakura zvigaba zvealuminium zvine chinwiwa mukati.Iwo machira akagadzirwa neUHMW zvinhu, uye akagamuchirwa Series 100BIP, simbi isina tsvina ine mazino gumi, uye Stainless simbi drive/idler shaft mu50mm x 50mm saizi.Mafomu ekuverenga akakodzera ndeaya anotevera.

Kuunganidza kufambisa - Wf

FORMULA :	Wf = WP × FBP × PP
	Wf = 80 × 0.4 × 1 = 32 ( Kg / M )

Kuverengera kweyuniti theory tension - TB

FORMULA :	TB =〔 (WP + 2 WB) × FBW + Wf 〕× L + (WP × H)
	TB =〔 ( 100 + ( 2 × 8.6 ) × 0.12 + 32 〕× 6 + 0 = 276.4 (kg / M)

Kuverengera kweyuniti tension- TW

FORMULA :	TW = TB × FA
	TW = 276.4 × 1.6 = 442 ( Kg / M )
	TWS = 2 TW = 884 Kg / M
	TWS yayo iri pakati pekutyaira

Kuverengera kweyuniti inotenderwa tension - TA

FORMULA :	TA = BS × FS × FT
	TA = 1445 × 1.0 × 0.95 = 1372 ( Kg / M )
	Nekuda kweTA kukosha kwakakura kupfuura TW, Naizvozvo, kutora neHS-100 ndiko kusarudzwa kwakakodzera.

Ndokumbira utarise kuSprocket spacing yeHS-100 muDrive Sprockets Chapter;iyo yakanyanya sprocket spacing ingangoita 120mm yeiyi dhizaini.
Deflection ratio ye drive shaft - DS

FORMULA :	SL = (TW + SW) × BW
	SL = ( 884 + 19.87 ) × 2 = 1807 ( Kg )
	DS = 5 × 10-4 [ ( SL × SB3 ) / ( E × I )]
	DS = 5 × 10-4 × [ ( 1791 × 21003 ) / ( 19700 × 1352750 )] = 0.3 mm
	Kana mhedzisiro yekuverenga iri diki pane yakajairwa kukosha yakanyorwa muDeflection Table;kutora maviri bhora mabheji zvakakwana kune system.

Kuverenga kwe shaft torque - TS

FORMULA :	TS = TWS × BW × R
	TS = 884 × 2 × 97 = 171496 ( kg - mm)
	Mukuenzanisa neMaximum Torque Factor muShaft Selection unit, tinoziva kuti kushandiswa kwe50mm × 50mm square shaft kwakachengeteka uye kwakakodzera kusarudzwa.

Kuverenga kweHorsepower - HP

FORMULA :	HP = 2.2 × 10-4 [ ( TS × V ) / R ]
	HP =2.2 ×10-4 × [ ( 171496 × 4) / 82] = 1.84 (HP)
	Kazhinji, iyo mechanic simba rekutendeuka conveyor inogona kurasikirwa ne25% panguva yekushanda.
	MHP = [ 1.84 / ( 100 - 25 )] × 100 = 2.45 ( HP )
	Kutora iyo 3HP drive mota ndiyo sarudzo chaiyo.

Incline Conveyor

The incline conveyor system inoratidzwa pamufananidzo uri pamusoro wakagadzirirwa washihg miriwo.Kureba kwayo kwakamira i4M, kureba kwese kweconveyor i10M, uye hupamhi hwebhandi i900mm.Inoshanda munzvimbo ine mwando nekumhanya kwe20M/min kutakura pizi pa60Kg/M2.Iwo machira anogadzirwa neUHMW zvinhu, uye bhandi rekutakura iHS-200B ine 50mm (H) ndege uye 60mm (H) varindi vepadivi.Sisitimu inotanga muchimiro isina kutakura zvigadzirwa, uye inoramba ichishanda ingangoita 7.5hours.Iyo zvakare inotora nema sprockets ane mazino gumi nemaviri uye simbi isina tsvina 38mm x 38mm drive/idler shaft.Mafomu ekuverenga akakodzera ndeaya anotevera.

Kuverengera kweyuniti theory tension - TB

FORMULA :	TB =〔(WP + 2WB) × FBW + Wf 〕× L + (WP × H)
	TB =〔( 60 + ( 2 × 4.4 ) × 0.12 + 0 ) 〕× 10 + ( 60 × 4 ) = 322.6 ( kg / M )
	Nekuda kweiyo haisi murwi wekutakura,Wf inogona kufuratirwa.

Kuverengera kweyuniti kushushikana - TW

FORMULA :	TW = TB × FA
	TW = 322.6 × 1.6 = 516.2 ( Kg / M )

Kuverengera kweyuniti inotenderwa tension - TA

FORMULA :	TA = BS × FS × FT
	TA = 980 × 1.0 × 0.95 = 931
	Nekuda kwekukosha TA yakakura kupfuura TW;saka, kutora HS-200BFP conveyor bhandi isarudzo yakachengeteka uye yakakodzera.

Ndokumbira utarise kuSprocket spacing yeHS-200 muDrive Sprockets Chapter;iyo yakakura sprocket spacing ingangoita 85mm yeiyi dhizaini.
Deflection ratio ye drive shaft - DS

FORMULA :	SL = (TW + SW) × BW
	SL = ( 516.2 + 11.48 ) × 0.9 = 475 Kg

FORMULA :	DS = 5 × 10-4 × [ ( SL x SB3 ) / ( E x I )]
	DS = 5 × 10-4 × [ ( 475 × 10003 ) / ( 19700 × 174817 ) ] = 0.069 mm
	Kana mhedzisiro yekuverenga iri diki pane yakajairwa kukosha yakanyorwa muDeflection Table;kutora maviri bhora mabheji zvakakwana kune system.

Kuverenga kwe shaft torque - TS

FORMULA :	TS = TW × BW × R
	TS = 322.6 × 0.9 × 49 = 14227 ( kg - mm)
	Mukuenzanisa neMaximum Torque Factor muShaft Selection unit, tinoziva kuti kushandiswa kwe38mm × 38mm square shaft kwakachengeteka uye kwakakodzera kusarudzwa.

Kuverenga kweHorsepower - HP

FORMULA :	HP = 2.2 × 10-4 × [ ( TS × V ) / R ]
	HP = 2.2 × 10-4 × [ ( 14227 × 20) / 49] = 1.28 ( HP )
	Kazhinji, iyo mechanic simba rekutendeuka conveyor inogona kurasikirwa ne20% panguva yekushanda.
	MHP = [ 1.28 / ( 100 - 20 )] × 100 = 1.6 ( HP )
	Kutora iyo 2HP drive mota ndiyo sarudzo chaiyo.

Kushandura Conveyor

A turning conveyor system iri pamusoro apa idhigirii 90 inotenderedza conveyor. Iwo machira ekudzoka nenzira yekutakura ese akagadzirwa neHDPE zvinhu.Upamhi hwebhandi rekutakura i500mm;inotora bhandi reHS-500B uye sprockets ine mazino makumi maviri nemana.Kureba kweiyo yakatwasuka chikamu chekumhanya ndeye 2M painogumira kupera uye 2M kumagumo ekutyaira.Radhiyasi yayo yemukati ndeye 1200mm.Iyo friction factor yezvipfeko uye bhandi ndeye 0.15.Zvinhu zvekutakura zvinhu mabhokisi emabhokisi pa60Kg/M2.The conveyor operation speed is 4M/min, uye inoshanda munzvimbo yakaoma.Maverengero anoenderana anotevera.

Kuverengera kweyuniti kushushikana - TWS

FORMULA :	TWS = (TN)
	Kushushikana kwakazara kwechikamu chekutyaira munzira yekutakura.
	T0 = 0
	T1 = WB + FBW × LR × WB
	T1 = 5.9 + 0.35 × 2 × ( 5.9) = 10.1

FORMULA :	TN = ( Ca × TN-1 ) + ( Cb × FBW × RO ) × WB
	Kushushikana kwechikamu chekutendeuka munzira yekudzoka.Nekukosha kweCa uye Cb, ndapota tarisa kune Tafura Fc.
	T2 = ( Ca × T2-1 ) + ( Cb × FBW × RO ) × WB
	TN = ( Ca × T1 ) + ( Cb × FBW × RO ) × WB
	T2 = ( 1.27 × 10.1) + ( 0.15 × 0.35 × 1.7) × 5.9 = 13.35

FORMULA :	TN = TN-1 + FBW × LR × WB
	Kushushikana kwechikamu chakatwasuka munzira yekudzoka.
	T3 = T3-1 + FBW × LR × WB
	T3 = T2 + FBW × LR × WB
	T3 = 13.35 + 0.35 × 2 × 5.9 = 17.5

FORMULA :	TN = TN-1 + FBW × LP × ( WB + WP )
	T4 = T4-1 + FBW × LP × ( WB + WP )
	T4 = T3 + FBW × LP × ( WB + WP )
	T4 = 17.5 + 0.35 × 2 × ( 5.9 + 60 ) = 63.6
	Kushushikana kwechikamu chakatwasuka munzira yekutakura.

FORMULA :	TN = ( Ca × TN-1 ) + ( Cb × FBW × RO ) × ( WB + WP )
	Kushushikana kwechikamu chekutendeuka munzira yekudzoka.Nekukosha kweCa uye Cb, ndapota tarisa kune Tafura Fc.
	T5 = ( Ca × T5-1 ) + ( Cb × FBW × RO ) × ( WB + WP )
	T5 = ( Ca × T6 ) + ( Cb × FBW × RO ) × ( WB + WP )
	T5 = ( 1.27 × 63.6) + ( 0.15 × 0.35 × 1.7) × ( 5.9 + 60) = 86.7

Total belt tension TWS (T6)

FORMULA :	TWS = T6 = TN-1 + FBW × LP × ( WB + WP )
	Kushushikana kwakazara kwechikamu chakatwasuka munzira yekutakura.
	T6 = T6-1 + FBW × LP × ( WB + WP )
	T6 = T5 + FBW × LP × ( WB + WP )
	T6 = 86.7 + 0.35 × 2 × ( 5.9 + 60 ) = 132.8 ( Kg / M )

Kuverengera kweyuniti inotenderwa tension - TA

FORMULA :

TA = BS × FS × FT

	TA = 2118 × 1.0 × 0.95 = 2012 ( Kg / M )
	Nekuda kwekukosha TA yakakura kupfuura TW;saka, kutora Series 500B conveyor bhandi isarudzo yakachengeteka uye yakakodzera.

Ndokumbira utarise kuSprocket spacing yeHS-500 muDrive Sprockets Chapter;iyo yakakura sprocket spacing inosvika 145mm.
Deflection ratio ye drive shaft - DS

FORMULA :	SL = ( TWS + SW ) ×BW
	SL = ( 132.8 + 11.48 ) × 0.5 = 72.14 ( Kg )

FORMULA :	DS = 5 × 10-4 × [ ( SL × SB3 ) / ( E × I )]
	DS = 5 × 10-4 × [ ( 72.14 × 6003) / ( 19700 × 174817 ) ] = 0.002 ( mm)
	Kana mhedzisiro yekuverenga iri diki pane yakajairwa kukosha yakanyorwa muDeflection Table;kutora maviri bhora mabheji zvakakwana kune system.

Kuverenga kwe shaft torque - TS

FORMULA :	TS = TWS × BW × R
	TS = 132.8 × 0.5 × 92.5 = 6142 ( kg - mm)
	Mukuenzanisa neMaximum Torque Factor muShaft Selection unit, tinoziva kuti kushandiswa kwe50mm × 50mm square shaft kwakachengeteka uye kwakakodzera kusarudzwa.

Kuverenga kweHorsepower - HP

FORMULA :	HP = 2.2 × 10-4 × [ ( TS × V / R )]
	HP = 2.2 × 10-4 × [ ( 6142 × 4) / 95] = 0.057 ( HP )
	Kazhinji, iyo mechanic simba rekutendeuka conveyor inogona kurasikirwa ne30% panguva yekushanda.
	MHP = [ 0.057 / ( 100 - 30 )] × 100 = 0.08 ( HP )
	Kutora iyo 1/4HP drive mota ndiyo sarudzo chaiyo.

Serial Turning Conveyor

Iyo serial inotenderedza conveyor system inogadzirwa maviri 90 madhigirii madhigirii ane nzira yakatarisana.Iwo machira mukudzoka uye nzira yekutakura ese ari maviri akagadzirwa neHDPE zvinhu.Kufara kwebhandi rekutakura i300mm;inotora bhandi reHS-300B uye sprockets ane mazino gumi nemaviri.Kureba kwechikamu chakatwasuka chinomhanya 2M kumagumo asina basa, 600mm munzvimbo yekubatanidza, uye 2M pamagumo ekutyaira.Iyo yemukati radius ndeye 750mm.Iyo friction factor yezvipfeko uye bhandi ndeye 0.15.Zvinhu zvekutakura zvinhu mabhokisi epurasitiki pa40Kg/M2.The conveyor operation speed is 5M/min, uye inoshanda munzvimbo yakaoma.Maverengero anoenderana anotevera.

Kuverengera kweyuniti kushushikana - TWS

FORMULA :	TWS = (TN)
	T0 = 0
	Kushushikana kwakazara kwechikamu chekutyaira munzira yekutakura.
	T1 = WB + FBW × LR × WB
	T1 = 5.9 + 0.35 × 2 × 5.9 = 10.1

FORMULA :	TN = ( Ca × TN-1 ) + ( Cb × FBW × RO ) × WB
	Kushushikana kwechikamu chekutendeuka munzira yekudzoka.Nekukosha kweCa uye Cb, ndapota tarisa kune Tafura Fc.
	T2 = ( Ca × T2-1 ) + ( Cb × FBW × RO ) × WB
	T2 = ( Ca × T1 ) + ( Cb × FBW × RO ) × WB
	T2 = ( 1.27 × 10.1) + ( 0.15 × 0.35 × 1.05) × 5.9 = 13.15

FORMULA :	TN = TN-1 + FBW × LR × WB
	Kushushikana kwechikamu chakatwasuka munzira yekudzoka.
	T3 = T3-1 + FBW × LR × WB
	T3 = T2 + FBW × LR × WB
	T3 = 13.15 + ( 0.35 × 0.6 × 5.9 ) = 14.3

FORMULA :	TN = ( Ca × TN-1 ) + ( Cb × FBW × RO ) × WB
	Kushushikana kwechikamu chekutendeuka munzira yekudzoka.Nekukosha kweCa uye Cb, ndapota tarisa kune Tafura Fc.
	T4 = ( Ca × T4-1 ) + ( Cb × FBW × RO ) × WB
	TN = ( Ca × T3 ) + ( Cb × FBW × RO ) × WB
	T4 = ( 1.27 × 14.3) + ( 0.15 × 0.35 × 1.05) × 5.9 = 18.49

FORMULA :	TN = TN-1 + FBW × LR × WB
	Kushushikana kwechikamu chakatwasuka munzira yekudzoka.
	T5 = T5-1 + FBW × LR × WB
	T5 = T4 + FBW × LR × WB
	T5 = 18.49 + ( 0.35 × 2 × 5.9 ) = 22.6

FORMULA :	TN = TN-1 + FBW × LP × ( WB + WP )
	Kushushikana kwechikamu chakatwasuka munzira yekutakura.
	T6 = T6-1 + FBW × LP × ( WB + WP )
	T6 = T5 + FBW × LP × ( WB + WP )
	T6 = 22.6 + [ ( 0.35 × 2 × ( 5.9 + 40 ) ] = 54.7

FORMULA :	TN = ( Ca × TN-1 ) + ( Cb × FBW × RO ) × ( WB + WP )
	Kushushikana kwechikamu chekutendeuka munzira yekutakura.Nekukosha kweCa uye Cb, ndapota tarisa kune Tafura Fc
	T7 = ( Ca × T7-1 ) + ( Cb × FBW × RO ) × ( WB + WP )
	T7 = ( Ca × T6 ) + ( Cb × FBW × RO ) × ( WB + WP )
	T7 = ( 1.27 × 54.7) + ( 0.15 × 0.35 × 1.05) × ( 40 + 5.9) = 72

FORMULA :	TN = TN-1 + FBW × LP × ( WB + WP )
	Kushushikana kwechikamu chakatwasuka munzira yekutakura.
	T8 = T8-1 + FBW × LP × ( WB + WP )
	TN = T7 + FBW × LP × ( WB + WP )
	T8 = 72 + [ ( 0.35 × 0.5 × ( 40 + 5.9 ) ] = 80

FORMULA :	TN = ( Ca × TN-1 ) + ( Cb × FBW × RO ) × ( WB + WP )
	Kushushikana kwechikamu chekutendeuka munzira yekutakura.Nekukosha kweCa uye Cb, ndapota tarisa kune Tafura Fc
	T9 = ( Ca × T9-1 ) + ( Cb × FBW × RO ) × ( WB + WP )
	T9 = ( Ca × T8 ) + ( Cb × FBW × RO ) × ( WB + WP )
	T9 = ( 1.27 × 80) + ( 0.15 × 0.35 × 1.05) × ( 40 + 5.9) =104

Total belt tension TWS (T6)

FORMULA :	TWS = T10
	Kushushikana kwakazara kwechikamu chakatwasuka munzira yekutakura.
	TN = TN-1 + FBW × LP × ( WB + WP )
	T10 = T10-1 + FBW × LP × ( WB + WP )
	T10 = 104 + 0.35 × 2 × ( 5.9 + 40 ) = 136.13 ( Kg / M )

Kuverengera kweyuniti inotenderwa tension - TA

FORMULA :	TA = BS × FS × FT
	TA = 2118 × 1.0 × 0.95 = 2012 ( Kg / M )
	Nekuda kwekukosha TA yakakura kupfuura TW;saka, kutora Series 300B conveyor bhandi isarudzo yakachengeteka uye yakakodzera.

Ndokumbira utarise kuSprocket spacing muDrive Sprockets Chitsauko;iyo yakakura sprocket spacing inosvika 145mm.
Deflection ratio ye drive shaft - DS

FORMULA :	SL = ( TWS + SW) × BW
	SL = ( 136.13 + 11.48 ) × 0.3 = 44.28 ( Kg )

FORMULA :	DS = 5 × 10-4 × [ ( SL × SB3 ) / ( E x I )]
	DS = 5 × 10-4 ×[ ( 44.28 × 4003) / ( 19700 × 174817 ) = 0.000001 ( mm)
	Kana mhedzisiro yekuverenga iri diki pane yakajairwa kukosha yakanyorwa muDeflection Table;kutora maviri bhora mabheji zvakakwana kune system.

Kuverenga kwe shaft torque - Ts

FORMULA :	TS = TWS × BW × R
	TS = 136.3 × 0.3 × 92.5 = 3782.3 ( kg - mm)
	Mukuenzanisa neMaximum Torque Factor muShaft Selection unit, tinoziva kuti kushandiswa kwe38mm × 38mm square shaft kwakachengeteka uye kwakakodzera kusarudzwa.

Calc, ulat, io, n of horsepower - HP

FORMULA :	HP = 2.2 × 10-4 × [ ( TS × V ) / R ]
	HP = 2.2 × 10-4 × [ ( 3782.3 × 5) / 92.5] = 0.045 ( HP )
	Kazhinji, simba remagetsi repakati drive conveyor rinogona kurasikirwa ne30% panguva yekushanda.
	MHP = [ 0.045 / ( 100 - 30 )] × 100 = 0.06 ( HP )
	Kutora iyo 1/4HP drive mota ndiyo sarudzo chaiyo.

Spiral Conveyor

Mifananidzo iri pamusoro apa muenzaniso we spiral conveyor system ine mitsara mitatu.Iwo machira ekupfeka enzira yekutakura uye nzira yekudzoka inogadzirwa neHDPE zvinhu.Iyo yakazara bhandi hupamhi i500mm uye inotora HS-300B-HD uye iyo sprockets ine mazino masere.Kureba kwechikamu chakatwasuka chekutakura mudhiraivha uye idler kupera ndeye 1 mita zvichiteerana.Iyo yemukati inotenderera radius ndeye 1.5M, uye zvinhu zvekutakura ndiwo mabhokisi etsamba pa50Kg/M2.Kumhanya kwekufambisa kwemutakuri ndeye 25M/min, kurerekera kuhurefu hwe4M uye kushanda munzvimbo yakaoma.Maverengero anoenderana anotevera.

Kuverengera kweyuniti kushushikana - TWS

FORMULA :	TW = TB × FA
	TWS = 958.7 × 1.6 = 1533.9 ( Kg / M )

FORMULA :	TB = [ 2 × R0 × M + ( L1 + L2 ) ] ( WP + 2 WB ) × FBW + ( WP × H )
	TB = [ 2 × 3.1416 × 2 × 3 + ( 1 + 1)] ( 50 + 2 × 5.9) × 0.35 + ( 50 × 2)
	TB = 958.7 ( Kg / M )

Kuverengera kweyuniti inotenderwa tension - TA

FORMULA :	TA = BS × FS × FT
	TA = 2118 × 1.0 × 0.95 = 2012 ( Kg / M )
	Nekuda kwekukosha TA yakakura kudarika TW;saka, tora Series 300B-HD bhandi isarudzo yakachengeteka uye yakakodzera.

Ndokumbira utarise kuSprocket spacing yeHS-300 muDrive Sprockets Chapter;iyo yakakura sprocket spacing inosvika 145mm.
Deflection ratio ye drive shaft - DS

FORMULA :	SL = ( TWS + SW) × BW
	SL = ( 1533.9 + 11.48 ) × 0.5 = 772.7 ( Kg )

FORMULA :	DS = 5 × 10-4 ×[ ( SL × SB3 ) / ( E × I )]
	DS = 5 × 10-4 ×[ ( 772.7 × 6003) / ( 19700 ×174817 )] = 0.024 ( mm)

Kana mhedzisiro yekuverenga iri diki pane yakajairwa kukosha yakanyorwa muDeflection Table;kutora maviri bhora mabheji zvakakwana kune system.
Kuverenga kwe shaft torque - TS

FORMULA :	TS = TWS × BW × R
	TS = 1533.9 × 0.5 × 92.5 = 70942.8 ( kg - mm)
	Mukuenzanisa neMaximum Torque Factor muShaft Selection unit, tinoziva kuti kushandiswa kwe38mm × 38mm square shaft kwakachengeteka uye kwakakodzera kusarudzwa.

Kuverengera simba remabhiza - HP